HMC5843
To change the measurement mode to continuous measurement mode, after the 8.3 milli-second power-up time send the
three bytes:
0x3C 0x02 0x00
This writes the 00 into the second register or mode register to switch from single to continuous measurement mode
setting. With the data rate at the factory default of 10Hz updates, a 100 milli-second delay should be made by the I2C
master before querying the HMC5843 data registers for new measurements. To clock out the new data, send:
0x3D, and clock out DXRA, DXRB, DYRA, DYRB, DZRA, DZRB located in registers 3 through 8. The HMC5843 will
automatically re-point back to register 3 for the next 0x3D query, expected 100 milli-seconds or later. All six data registers
must be read properly before new data can be placed in any of these data registers.
SELF TEST OPERATION
To check the HMC5843 for proper operation, a self test feature in incorporated in which the sensor offset straps are
excited to create a nominal field strength (bias field) to be measured. To implement this self test, the least significant bits
(MS1 and MS0) of configuration register A are changed from 00 to 01.
Then, by placing the mode register into single-conversion mode (0x01), two data acquisition cycles will be made on each
magnetic vector. The first acquisition will be a set pulse followed shortly by measurement data of the external field. The
second acquisition will have the offset strap excited in the positive bias mode (~5.5mA in offset straps) to create about a
0.55 gauss self test field plus the external field. The first acquisition values will be subtracted from the second acquisition,
and the net measurement will be placed into the data output registers.
If the configuration register B is left at the factory default value of 0x20, values around +715 ADC counts (0.55Ga * 1300
counts/Ga) will be placed in the data output registers. To leave the self test mode, change MS1 and MS0 bit of the
configuration register A back to 0x00. Also change the mode register if single-conversion mode is not the intended next
mode of operation.
SCALE FACTOR CALIBRATION
Using the method described above in section SELF TEST OPERATION, user can scale sensor s’ sensitivity to match each
other. Since placing device in positive bias mode (or alternatively negative bias mode) applies the same artificial field on
all three axes, the resulting ADC measurement in data output registers can be used to scale the sensors.
Alternatively, the built-in self test can be used to periodically compensate the scaling errors due to temperature variations.
A compensation factor can be found by comparing the self test outputs with the ones obtained at a known temperature.
For example, if the self test output is 715 at room temperature and 730 at the current temperature then a scale factor of
(715/730) should be applied to all current magnetic readings. A temperature sensor is not required to use this method.
EXTERNAL CAPACITORS
The two external capacitors should be ceramic type construction with low ESR characteristics. The exact ESR values are
not critical but values less than 200 milli-ohms are recommended. Reservoir capacitor C1 is nominally 4.7 μF in
capacitance, with the set/reset capacitor C2 nominally 0.22 μF in capacitance. Low ESR characteristics may not be in
many small SMT ceramic capacitors (0402), so be prepared to up-size the capacitors to gain Low ESR characteristics.
www.honeywell.com
19
相关PDF资料
HMC5983-DEMO BOARD DEMO 3AXIS COMPASS HMC5983
HMC6343-EVAL EVAL BOARD FOR HMC6343
HMR2300-D21-232-DEMO KIT DEVELOP MAGNETOMETER RS232
HMR3000-DEMO-232 KIT DEMO DIG COMPASS MODUL RS232
HMU-PATBH101KQ-3M CABLE ASSEMBLY MU FIBER OPTIC 3M
HP-BRACKET ACCY BRACKET FOR HP RELAYS
HP100SS HOLE PLUG 1" STAINLESS STEEL
HP100 HOLE PLUG 1" STEEL
相关代理商/技术参数
HMC5843-EVAL 功能描述:BOARD EVALUATION FOR HMC5843 RoHS:是 类别:编程器,开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-
HMC5843-TR 功能描述:SENSOR MAGNETIC 3 AXIS 20-LCC RoHS:是 类别:传感器,转换器 >> 磁性 - 霍尔效应,数字式开关,线性,罗盘 (IC) 系列:HMC 标准包装:1 系列:- 传感范围:20mT ~ 80mT 类型:旋转 电源电压:4.5 V ~ 5.5 V 电流 - 电源:15mA 电流 - 输出(最大):- 输出类型:数字式,PWM,8.5 位串行 特点:可编程 工作温度:-40°C ~ 150°C 封装/外壳:20-SSOP(0.209",5.30mm 宽) 供应商设备封装:20-SSOP 包装:Digi-Reel® 其它名称:AS5132-HSST-500DKR
HMC5846LS6 功能描述:RF Amplifier IC VSAT, DBS 12GHz ~ 16GHz 16-SMT (6x6) 制造商:analog devices inc. 系列:- 包装:带卷(TR) 零件状态:生命周期结束 频率:12GHz ~ 16GHz P1dB:34.5dBm 增益:31dB 噪声系数:- RF 类型:VSAT,DBS 电压 - 电源:7V 电流 - 电源:1.2A 测试频率:12GHz ~ 16GHz 封装/外壳:16-TFQFN 裸露焊盘 供应商器件封装:16-SMT(6x6) 标准包装:1
HMC584LP5 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 12.5 - 13.9 GHz
HMC584LP5_10 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:MMIC VCO w/ HALF FREQUENCY OUTPUT & DIVIDE-BY-4, 12.5 - 13.9 GHz
HMC584LP5E 制造商:Hittite Microwave Corp 功能描述:IC MMIC VCO HBT BIPOLAR 32-QFN
HMC584LP5ETR 功能描述:RF IC VCO General Purpose 12.5GHz ~ 13.9GHz Triple Outputs (Divide by 2, Divide by 4, Standard) 32-QFN (5x5) 制造商:analog devices inc. 系列:- 包装:剪切带(CT) 零件状态:有效 功能:VCO 频率:12.5GHz ~ 13.9GHz RF 类型:通用 辅助属性:三路输出(除以 2,除以 4,标准) 封装/外壳:32-VFQFN 裸露焊盘 供应商器件封装:32-QFN(5x5) 标准包装:1
HMC585MS8G 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:HIGH IP3 GaAs MMIC MIXER with INTEGRATED LO AMPLIFIER, 400 - 650 MHz